Application of artificial neural network method to predict the breakage properties of PGE bearing chromite ore

In the present investigation, systematic grinding experiments were conducted in a laboratory ball mill to determine the breakage properties of low-grade PGE bearing chromite ore. The population balance modeling technique was used to study the breakage parameters such as primary breakage distribution (B_{i, j}) and the specific rates of breakage (S_i). The breakage and selection function values were determined for six feed sizes. The results stated that the breakage follows the first-order grinding kinetics for all the feed sizes. It was observed that the coarser feed sizes exhibit higher selection function values than the finer feed size. Further, an artificial neural network was used to predict breakage characteristics of low-grade PGE bearing chromite ore. The predicted results obtained from the neural network modeling were close to the experimental results with a correlation of determination R² = 0.99 for both product size and selection function.     

Catalysts by pyrolysis: Direct observation of transformations during re-pyrolysis of transition metal-nitrogen-carbon materials leading to state-of-the-art platinum group metal-free electrocatalyst

Transition metal-nitrogen-carbon (M-N-C) materials have been the focus of scientists’ efforts to address the rising need for earth-abundant materials solutions for energy technology and decarbonization of the economy. They are viewed as one of the most promising candidates to replace platinum group metal (PGM) catalysts in the fuel cell and energy conversion fields, including the application of oxygen reduction reaction, carbon dioxide reduction reaction, and nitrogen reduction reaction. In the effort to improve M-N-C materials properties and achieve atomic dispersity of the transition metal in the carbonaceous matrix, a re-pyrolysis process has been proposed. This secondary heat treatment process of already obtained primary pyrolysis-derived M-N-C materials has been widely reported to substantially improve the electrochemical performance and operational stability of the catalysts. Here, we report a systematic investigation of this process used on samples of templated M-N-C catalysts to obtain state-of-the-art catalysts via in situ heating X-ray photoelectron spectroscopy (XPS), scanning transmission electron microscopy (STEM), energy-dispersive X-ray spectroscopy (EDS), electron energy loss spectroscopy (EELS), X-ray diffraction (XRD), and X-ray computed tomography (CT) characterization methods. It is found that the re-pyrolysis of M-N-C materials could result in the partial amorphization of the carbonaceous substrate. It causes the rearrangement and transformation of multitudinous N moieties, leading to optimization of their morphological display and association with atomically dispersed transition metal dopants. Ultimately, the re-pyrolysis results in an increase in uniformity of the active Fe-N_x sites distribution without the formation of nano-crystalline phases (metallic or carbide) and with overall preservation of the morphology of the carbonaceous framework achieved during the first formative pyrolysis step of the templated synthesis. These observations provide confirmation that empirically established re-pyrolysis is recommended to be used on all M-N-C materials despite the different synthesis routes to obtain a practical advanced catalytic material.     

双对苯醌的抗氧化活性分析及其固体发酵条件优化

为探索生物活性未知的双对苯醌（2,7-dihydroxy-3,6,9-trimethyl-9H-xanthene-1,4,5,8-tetraone，DTXT）的抗氧化活性，并提高其发酵产量，考察DTXT的还原力以及对超氧阴离子自由基、羟自由基、1,1-二苯基-2-三硝基苯肼（1,1-diphenyl-2-picrylhydrazyl，DPPH）自由基的清除效果，在单因素试验基础上，采用响应面法优化了DTXT产生菌瓶生顶孢霉（Acremonium cavaraeanum）CA022菌株的固体发酵培养基。结果表明：在200 μg/mL质量浓度下，DTXT的还原力与芦丁差异不显著，高于VE和2,6-二叔丁基-4甲基苯酚，对超氧阴离子自由基清除率达到67.00%，对羟自由基清除率达到78.83%，对DPPH自由基清除率达到76.53%。通过响应面试验，得到最佳培养基配方为葡萄糖0.773%、硝酸钠0.185%、H3BO3 0.032%、VB1 100 μg/100 g，在此条件下实际获得的DTXT产量为4 150.8 mg/kg，是优化前产量的（2 864.83 mg/kg）1.45 倍。     

Preparation of Pt/Ce–Zr–Y mixed oxide/anodized aluminium oxide catalysts for hydrogen passive autocatalytic recombination

The use of a Pt-based catalyst was evaluated for autocatalytic hydrogen recombination. The Pt was supported on a mixture of Ce-, Zr- and Y-oxides (CZY) to yield nanosized Pt particles. The Pt/CZY/AAO catalyst was then prepared by the spray-deposition of the Pt/CZY intermediate onto an anodized aluminium oxide (AAO) layer on a metallic aluminum core. The Pt/CZY/AAO catalyst (3 × 1 cm) was evaluated for hydrogen combustion (1–8 vol% hydrogen in the air) in a recombiner section testing station. The thermal distribution throughout the catalyst surface was investigated using an infrared camera. The maximum temperature gradient (ΔT) for the examined hydrogen concentrations did not exceed 36 °C. The Pt/CZY/AAO catalyst was also evaluated for prolonged hydrogen combustion duration to assess its durability. An average combustion temperature of 239.0 ± 10.0 °C was maintained for 53 days of catalytic hydrogen combustion, suggesting that there was limited, or no, catalyst deactivation. Finally, a Pt/CZY/AAO catalytic plate (14.0 × 4.5 cm) was prepared to investigate the thermal distribution. An average surface temperature of 212.5 °C and a maximum ΔT of 5.4 °C was obtained throughout the catalyst surface at a 3 vol% hydrogen concentration.     

High Q×f values of Zn-Ni co-modified LiMg0.9Zn0.1-xNixPO4 microwave dielectric ceramics for 5G/6G LTCC modules

In this work, Zn-Ni co-modified LiMg_0.9Zn_0.1-xNi_xPO₄ (x = 0–0.1) microwave dielectric ceramics were fabricated using a solid state synthesis route. Rietveld refinement of the XRD data revealed that all ceramic samples have formed a single phase with olivine structure. SEM images showed that the samples have a dense microstructure, that agrees with the measured relative density of 97.73 %. Based on the complex chemical bond theory, Raman and infrared reflectance spectra, we postulate that ε_r is mainly affected by the ionic polarizability, lattice and bond energy, while P-O bond plays a decisive role in Q×f and τ_f value. Optimum properties of Q×f ~ 153,500 GHz, ε_r ~ 7.13 and τ_f ~ ?59 ppm/°C were achieved for the composition LiMg_0.9Zn_0.06Ni_0.04PO₄ sintered at 875 ℃ for 2 h. This set of properties makes these ceramics an excellent candidate for LTCC, wave-guide filters and antennas for 5 G/6 G communication applications.     

低压静电场辅助冷冻对竹笋品质的影响

为研究低压静电场辅助冷冻对竹笋冻结特性的影响，以冻结曲线、硬度、水分损失率、水分迁移、冰晶形态和组织微观结构为指标，探究低压静电场辅助冷冻（－35 ℃）和普通冷冻（－35 ℃）条件下竹笋品质的变化规律。结果表明：低压静电场辅助冷冻提高了冻结效率，改变了冰晶形态及分布，减轻了组织微观结构破损程度，改善了解冻汁液流失情况。与静电板间距10、20、30、40 cm处的冷冻竹笋解冻后水分损失率分别为14.16%、12.58%、9.73%、10.44%，显著低于对照组（21.01%）（P＜0.05），硬度分别为461.19、507.48、496.65 g和455.31 g，显著高于对照组（350.70 g）（P＜0.05）。低场核磁共振分析结果表明，在低压静电场辅助冷冻下竹笋解冻后汁液流失减少，扫描电子显微镜观察结果显示，竹笋纤维排列整齐，组织微观结构保持较好。低压静电场辅助冷冻可有效改善竹笋品质，可为利用低压静电场进行果蔬的冷冻贮藏和冷链运输提供参考。     

Designing amorphous formulations of polyphenols with naringin by spray-drying for enhanced solubility and permeability

Naringin (NAR), a major flavanone (FVA) glycoside, is a component of food mainly obtained from grapefruit. We used NAR as a food additive to improve the solubility and permeability of hydrophobic polyphenols used as supplements in the food industry. The spray-dried particles (SDPs) of NAR alone show an amorphous state with a glass transition temperature (T_g) at 93.2 °C. SDPs of hydrophobic polyphenols, such as flavone (FVO), quercetin (QCT), naringenin (NRG), and resveratrol (RVT) were prepared by adding varying amounts of NAR. All SDPs of hydrophobic polyphenols with added NAR were in an amorphous state with a single T_g, but SDPs of hydrophobic polyphenols without added NAR showed diffraction peaks derived from each crystal. The SDPs with NAR could keep an amorphous state after storage at a high humidity condition for one month, except for SDPs of RVT/NAR. SDPs with NAR enhanced the solubility of hydrophobic polyphenols, especially NRG solubility, which was enhanced more than 9 times compared to NRG crystal. The enhanced solubility resulted in the increased membrane permeability of NRG. The antioxidant effect of the hydrophobic NRG was also enhanced by the synergetic effect of NAR. The findings demonstrated that NAR could be used as a food additive to enhance the solubility and membrane permeability of hydrophobic polyphenols.     

Stabilization of natural gas foams using different surfactants at high pressure and high temperature conditions

Natural gas foam can be used for mobility control and channel blocking during natural gas injection for enhanced oil recovery, in which stable foams need to be used at high reservoir temperature, high pressure and high water salinity conditions in field applications. In this study, the performance of methane (CH₄) foams stabilized by different types of surfactants was tested using a high pressure and high temperature foam meter for surfactant screening and selection, including anionic surfactant (sodium dodecyl sulfate), non-anionic surfactant (alkyl polyglycoside), zwitterionic surfactant (dodecyl dimethyl betaine) and cationic surfactant (dodecyl trimethyl ammonium chloride), and the results show that CH₄-SDS foam has much better performance than that of the other three surfactants. The influences of gas types (CH₄, N₂, and CO₂), surfactant concentration, temperature (up to 110°C), pressure (up to 12.0 MPa), and the presence of polymers as foam stabilizer on foam performance was also evaluated using SDS surfactant. The experimental results show that the stability of CH₄ foam is better than that of CO₂ foam, while N₂ foam is the most stable, and CO₂ foam has the largest foam volume, which can be attributed to the strong interactions between CO₂ molecules with H₂O. The foaming ability and foam stability increase with the increase of the SDS concentration up to 1.0 wt% (0.035 mol/L), but a further increase of the surfactant concentration has a negative effect. The high temperature can greatly reduce the stability of CH₄-SDS foam, while the foaming ability and foam stability can be significantly enhanced at high pressure. The addition of a small amount of polyacrylamide as a foam stabilizer can significantly increase the viscosity of the bulk solution and improve the foam stability, and the higher the molecular weight of the polymer, the higher viscosity of the foam liquid film, the better foam performance.